Download the latest Cherry Mobile Stock Rom (original firmware, flash file) for all the available Cherry Mobile Smartphone and tablets for free. Home Firmware Download Cherry Mobile Stock Rom for all models. Updated on January 17, 2020. Cherry Mobile Flare XL Plus V2.0 Stock Firmware (Flash File) Model Name. Reset For ENTRY QPST Download CM Flare s100. Discussion started by gemboy01. Need cherry mobile flare lite 2s v1 firmware po.
Credit goes toRyan Rudolf Oba in Cherry Mobile FlareFB group
CWM for CM Flare / Karbonn A9+ reformats boot partition, but instead of reformatting boot partition 8, it reformats boot partition 3. When this happens, phone will not boot, even fastboot mode. Upon powering the phone, you will get the message ENTRY QPST DOWNLOAD.To fix this, we need to restore a working backup of partition3. Partition3 is FAT16 partition and contains AMSS.MBN and AMSSHD.MBN. It does not contain IMEI info. Your IMEI will be preserved if you will follow this guide accordingly.
Requirements –
1. Acronis True Image – The backup partition3 I will provide is created using Acronis. You will also need Acronis to restore this backup partition to your phone. I used Acronis True Image 2013. Don’t ask me where to get Acronis.
2. Backup partition3 – make sure that the file you have is Partition3sector_full_b1_s1_v1. If the filename does not match, it means I did not provide that file. There is a chance this will cause further damage. Proceed with caution.
Steps –
1. Power on Flare, it will show ENTRY QPST DOWNLOAD
2. Connect Flare to PC, install drivers if prompted. Use the PCDRIVERS.ZIP included with your Flare. I have also included it here.
3. Open Acronis True Image. (Picture1)
4. Click on Backup and Recovery > Browse for Backup. (Picture2)
5. Navigate to where you saved the backup partition3. Press Add to Backup List. (Picture3)
6. Press Recover > Disk recovery options. Put a checkmark on Recover sector-by-sector. Press OK. (Picture4)
7. Make sure source and destination is the same 40MB. Be careful on this one, if done incorrectly it will cause further damage. Press Recover now. (Picture5)
8. Wait until recovery process is complete. (Picture6, Picture7)
9. Press Restart after recovery is completed. (Picture8)
10. Disconnect Flare from PC, remove / reconnect battery.
11. Reboot Flare and enjoy!
DO NOT USE THE FORMAT BOOT FUNCTION OF CWM. It formats partition3 instead of partition8.
credits to ryanrudolf, opaw ko aka ako si opaw (for the idea), newbie (for confirming IMEI partitions)
Download here:Share to gain access to file
Hi,
Here is an alternative way to Fix Cherry Mobile Flare S100 via 'more difficult' eMMC Test Points. You should only do this if:
1. Boot Repair via QPST eMMC Software Download gives you 'Cookie not found' error.
2. ATF JTAG Factory Restore Does not work (gives you error eMMC Busy).
1. You did not Activate JTAG and want to do via eMMC TP only.
How is this more difficult than JTAG?
1. You need to remove the metallic Shield under the back sticker of the phone.
2. The Test Point locations are very small and you need to have a microscope and good soldering skills.
3. You need to remove 1 resistor to make the Connection stable, and then replace this resistor with a 'jumper wire' or just solder lead after the Full Factory Restore is done.
4. It takes 3 hours to restore 800 mb to the phone via eMMC TP while it only takes 40 minutesto do the same task via JTAG.
For those of you who want to continue, here is the eMMC Test Point
Connections... (You need ATF 10.11 from Auto Update Server).
Here is the Phone All Wire Up:
Some Screenshot half-way Through:
And here is the phone after 3 hours...:
Where is the 800 mb Repair File Sir ???????????
Please wait, still uploading it...